Niagara Cutter N85536 Carbide Square Nose End Mill, Inch, Uncoated (Bright) Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 3.5″ Overall Length, 0.625″ Cutting Diameter, 0.625″ Shank Diameter

5/5
Recommend

If you looking for Niagara Cutter N85536 Carbide Square Nose End Mill, Inch, Uncoated (Bright) Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 3.5″ Overall Length, 0.625″ Cutting Diameter, 0.625″ Shank Diameter then you are in righ place. We search for Niagara Cutter N85536 Carbide Square Nose End Mill, Inch, Uncoated (Bright) Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 3.5″ Overall Length, 0.625″ Cutting Diameter, 0.625″ Shank Diameter in many merchants, compare product prices also product reviews to help you before decide to buy products. Please read carefully following informations:

Niagara Cutter N85536 Carbide Square Nose End Mill, Inch, Uncoated (Bright) Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 3.5″ Overall Length, 0.625″ Cutting Diameter, 0.625″ Shank Diameter Features

Four flutes produce a better finish than fewer flutes
Square nose end mills (also called square end) create sharp, unrounded cuts
Carbide can run at higher speeds than high-speed steel, resisting abrasion and high cutting temperatures
Uncoated (bright) tools have no additional surface treatment or coating for use on a broad range of materials
Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling

Niagara Cutter N85536 Carbide Square Nose End Mill, Inch, Uncoated (Bright) Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 3.5″ Overall Length, 0.625″ Cutting Diameter, 0.625″ Shank Diameter Description

The Niagara Cutter C430 uncoated carbide square nose end mill has four flutes and a 30-degree helix angle for general-purpose machining on a range of materials. The tools square end creates sharp, unrounded cuts, and the center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit. Four flutes produce a better finish than fewer flutes. The 30-degree helix angle supports general-purpose applications. It balances lower angles strong cutting edge for difficult-to-machine materials with higher angles increased cutting action.

The carbide substrate is harder than high-speed or cobalt steel, making it more wear resistant at high speeds and providing longer tool life. With no coating or surface treatment, this uncoated tool can be used on a broad range of materials. Cutting diameter tolerance is +0.000 to -0.002. The round shank accommodates a variety of holders.

End mills are designed to remove material and create multi-dimensional shapes and profiles. They have cutting edges along the outside diameter and flutes that remove chips from the cutting area and allow cooling fluids to enter. If heat is not reduced effectively, the tools cutting edges will dull and additional material buildup can occur. The number of flutes can range from two to eight. Two-flute designs offer the most efficient chip removal, but more flutes provide a smoother finish. The shank is the end of the tool held in place by a tool holder or machine. Center-cutting end mills can create three-dimensional shapes and profiles, and make plunge cuts similar to a drill bit. Non-center-cutting end mills are for applications such as peripheral milling and finishing, but cannot make plunge cuts.

Niagara Cutter has been designing and manufacturing precision cutting tools since 1954. Specializing in end mills, cutting mills, and saws, the company is based in New York and manufactures its tools at facilities in Pennsylvania and Massachusetts. This allows the company control over production, from substrate to coating, which is essential for customers in a variety of industries, especially aerospace and automotive.

Niagara Cutter N85536 Carbide Square Nose End Mill, Inch, Uncoated (Bright) Finish, Roughing and Finishing Cut, 30 Degree Helix, 4 Flutes, 3.5″ Overall Length, 0.625″ Cutting Diameter, 0.625″ Shank Diameter Related